All dimensions in millimetres. Subject to changes. 11 PLANNING DIMENSIONS All dimensions in millimetres Full overlay K0 Overlay K3 Half overlay K9.5 Inset 1 K19 84.5 3-7 F 12 24 13 F 84.5 3-7 24 15 10 3-7 84.5 31 2 x F 21.5 F 3.5 31 86 40.5 F 3-7 Mounting plate height 2 Mounting plate height 2 Mounting plate height 2 Mounting plate height 2 1 Set mounting plate back by door thickness +1.5 mm Door overlay 0 Cup distance 3 4 5 6 7 24.0 -2 23.0 -2 22.0 -2 0 21.0 -2 0 20.0 -2 0 2 19.0 0 2 3 18.5 18.0 0 2 3 17.5 17.0 2 3 16.5 16.0 2 3 15.5 15.0 3 Mounting plate height Door overlay 3 Cup distance 3 4 5 6 7 21.0 -2 20.0 -2 19.0 -2 0 18.0 -2 0 17.0 -2 0 2 16.5 16.0 0 2 3 15.5 15.0 0 2 3 14.5 14.0 2 3 13.5 13.0 2 3 12.5 12.0 3 Mounting plate height Door overlay 9.5 Cup distance 3 4 5 6 7 14.5 -2 13.5 -2 12.5 -2 0 11.5 -2 0 10.5 -2 0 2 10.0 9.5 0 2 3 9.0 8.5 0 2 3 8.0 7.5 2 3 7.0 6.5 2 3 6.0 5.5 3 Mounting plate height Door reveal 19 Cup distance 3 4 5 6 7 0.0 0 2 3 0.5 1.0 0 2 3 1.5 2.0 2 3 3.0 2 3 4.0 3 Mounting plate height MINIMUM GAP Door thickness Cup distance 3 4 5 6 7 24.0 1.0 1.0 1.0 1.22 2.12 22.0 1.0 1.0 1.0 1.0 1.52 21.0 1.0 1.0 1.0 1.0 1.22 20.0 1.0 1.0 1.0 1.0 1.0 19.0 1.0 1.0 1.0 1.0 1.0 18.0 1.0 1.0 1.0 1.0 1.0 17.0 1.0 1.0 1.0 1.0 1.0 16.0 1.0 1.0 1.0 1.0 1.0 Minimum gap 2 1.0 with 85° opening angle MINIMUM REVEAL Door thickness Cup distance 3 4 5 6 7 24.0 2.4 2.1 2.1 2.1 2.0 22.0 1.6 1.6 1.6 1.5 1.5 21.0 1.4 1.3 1.3 1.3 1.3 20.0 1.1 1.1 1.1 1.1 1.1 19.0 0.9 0.9 0.9 0.9 0.9 18.0 0.7 0.7 0.7 0.7 0.7 17.0 0.6 0.6 0.6 0.6 0.6 16.0 0.6 0.6 0.6 0.6 0.6 Minimum reveal (F) 85° OPENING ANGLE Door thickness Cup distance 3 4 5 6 7 36.0 11.1 10.3 9.7 9.1 8.5 30.0 5.4 4.8 4.4 4.3 4.2 28.0 3.7 3.6 3.5 3.4 3.3 26.0 2.9 2.8 2.8 2.7 2.6 24.0 2.2 2.1 2.1 2.1 2.0 22.0 1.6 1.6 1.6 1.5 1.5 21.0 1.4 1.3 1.3 1.3 1.3 20.0 1.1 1.1 1.1 1.1 1.1 19.0 0.9 0.9 0.9 0.9 0.9 18.0 0.7 0.7 0.7 0.7 0.7 16.0 0.6 0.6 0.6 0.6 0.6 Minimum reveal (F) 3 at 85° 3 85° opening angle reduction clip NOTES The minimum gap is the clearance required between the cabinet face and the closed door so that the door can be opened without hindrance. Minimum reveal for doors with chamfered edges (R = 1 mm) with factory setting. A trial fitting is recommended for door thicknesses from 24 mm. DRILLING PATTERNS 45/9.5 For screw fitting For press fitting 9.5 45 35+0.1 45 8 9.5 35+0.1 Impresso combination drilling pattern 45 8 9.5 35+0.1 48 8 9 35+0.1 CUP DIMENSIONS 39 (40.5) 62 (64.5) ( ) Impresso min. 12.6 3 (8) 39 (40.5) Hinge systems Tiomos 110
RkJQdWJsaXNoZXIy ODM0MzI=