15 All dimensions in millimetres. Subject to changes. Hinge systems DRILLING PATTERNS CUP DIMENSIONS For screw fitting 9.5 45 35+0.1 39 (40.5) 62 (64.5) ( ) Impresso min. 12.6 3 (8) 39 (40.5) PLANNING INFORMATION All dimensions in millimetres Full overlay K0 Overlay K3 Half overlay K9.5 Inset1 K19 84.5 3-7 F 12 24 13 F 84.5 3-7 24 15 10 3-7 84.5 31 2 x F 21.5 F 3.5 31 86 40.5 F 3-7 Mounting plate height 2 Mounting plate height 2 Mounting plate height 2 Mounting plate height 2 1Set the mounting plate back by the door thickness +1.5 mm Door overlay 0 Cup distance Door overlay 3 Cup distance Door overlay 9.5 Cup distance Door reveal 19 Cup distance 3 4 5 6 7 3 4 5 6 7 3 4 5 6 7 3 4 5 6 7 24.0 -2 21.0 -2 14.5 -2 0.0 0 2 3 23.0 -2 20.0 -2 13.5 -2 0.5 3.5 22.0 -2 0 19.0 -2 0 12.5 -2 0 1.0 0 2 3 21.0 -2 0 18.0 -2 0 11.5 -2 0 1.5 3.5 20.0 -2 0 2 17.0 -2 0 2 10.5 -2 0 2 2.0 2 3 19.0 0 2 3 16.5 10.0 3.0 2 3 18.5 3.5 16.0 0 2 3 9.5 0 2 3 4.0 3 18.0 0 2 3 15.5 3.5 9.0 3.5 17.5 3.5 15.0 0 2 3 8.5 0 2 3 17.0 2 3 14.5 3.5 8.0 3.5 16.5 3.5 14.0 2 3 7.5 2 3 16.0 2 3 13.5 3.5 7.0 3.5 15.5 3.5 13.0 2 3 6.5 2 3 15.0 3 12.5 3.5 6.0 3.5 14.5 3.5 12.0 3 5.5 3 11.5 3.5 5.0 3.5 Mounting plate height Mounting plate height Mounting plate height Mounting plate height MINIMUM GAP MINIMUM JOINT 85° OPENING ANGLE NOTICE Door thickness Cup distance Door thickness Cup distance Door thickness Cup distance The minimum gap is the clearance required between the front edge of the cabinet and the closed door so that the door can be opened without hindrance. Minimum reveal for doors with chamfered edges (R = 1 mm) with factory setting. A trial fitting is recommended for door thicknesses from 24 mm. 3 4 5 6 7 3 4 5 6 7 3 4 5 6 7 24.0 1.0 1.0 1.0 1.22 2.12 24.0 2.4 2.1 2.1 2.1 2.0 36.0 11.1 10.3 9.7 9.1 8.5 22.0 1.0 1.0 1.0 1.0 1.52 22.0 1.6 1.6 1.6 1.5 1.5 30.0 5.4 4.8 4.4 4.3 4.2 21.0 1.0 1.0 1.0 1.0 1.22 21.0 1.4 1.3 1.3 1.3 1.3 28.0 3.7 3.6 3.5 3.4 3.3 20.0 1.0 1.0 1.0 1.0 1.0 20.0 1.1 1.1 1.1 1.1 1.1 26.0 2.9 2.8 2.8 2.7 2.6 19.0 1.0 1.0 1.0 1.0 1.0 19.0 0.9 0.9 0.9 0.9 0.9 24.0 2.2 2.1 2.1 2.1 2.0 18.0 1.0 1.0 1.0 1.0 1.0 18.0 0.7 0.7 0.7 0.7 0.7 22.0 1.6 1.6 1.6 1.5 1.5 17.0 1.0 1.0 1.0 1.0 1.0 17.0 0.6 0.6 0.6 0.6 0.6 21.0 1.4 1.3 1.3 1.3 1.3 16.0 1.0 1.0 1.0 1.0 1.0 16.0 0.6 0.6 0.6 0.6 0.6 20.0 1.1 1.1 1.1 1.1 1.1 19.0 0.9 0.9 0.9 0.9 0.9 18.0 0.7 0.7 0.7 0.7 0.7 16.0 0.6 0.6 0.6 0.6 0.6 Minimum gap Minimum joint (F) Minimum joint (F)3 85° 2 1.0 with 85° opening angle 3 85° opening angle reduction clip TIOMOS
RkJQdWJsaXNoZXIy ODM0MzI=